How do I apply frosted window film (Bubble free)?
How do I apply frosted window film? Watch our instruction video on how to apply frosted window film.
Some general information about how to apply window film
Always, first read, our extensive general information here.
- Make sure to not apply window film in direct sunlight, make sure the temperature of the window film, the window itself and the surrounding air is -ideally- around 12 to 18 degrees Celsius. When the temperature is above 18 degrees we advise you to apply the window film during the early mornings or after sundown.
- Use 2 or more people when applying your frosted window film. One holding the top/left of the film and one holding the bottom/right to position the window film correctly. Subsequently, during application one holds the film a couple of centimetres above the surface, while the other cards with the squeegee, starting in the centre of the frosted window film.
- Extensively clean the window and the surrounding area, including you work environment. Clean it of durst, dirt, flies, spiders. Watch out for your fingerprint on the window glass itself.
How do I apply frosted window film? – Watch our instruction video.
In the video below you see how you apply frosted window film (cut).
How to apply frosted window film (bubble-free)?
Below you find instructions on how to apply your bespoke frosted window film (cut). You have been supplied with bubble free window film. So application without water is possible. If you are supplied with a WET APPLY frosted window film always use water.
- Always keep your frosted window film flat so that is does not bend/fold.
- Make sure to not apply window film in direct sunlight, make sure the temperature of the window film, the window it self and the surrounding air is -ideally- around 12 to 18 degrees Celsius. When the temperature is above 18 degrees we advise you to apply the window film during the early mornings or after sundown. The higher the temperature the more difficult it is to apply the frosted window film!
- Clean the window thoroughly. Remove paint, grease and other dirt. If any is left behind, it will always be visible!
- Also clean the surrounding area, like the window frame itself and your work environment. If you are applying near the ceiling and/or the ground make sure they are also clean. Also be wear of flying insects and pets.
- Use the supplied squeegee and card over the application-tape on the front of the frosted window film to further increase the binding between the two. Use a sturdy flat surface, like a table.
- Remove the backing paper. Carefully. When the film contains cut-outs/letters/elements, be very careful when removing the backing paper, as to not tear the film itself, when parts remain stuck to the backing paper. Take your time, most mistakes occur here!
- You are generally supplied with bubble free frosted window film. So no water is required. However, if you are inexperienced or are applying very large films with few cut-outs, you can use water, if you desire so. Use a plant sprayer to add a fine mist of water to the glass.
- Apply the window film with the application-tape to the window, position it at the preferred location.
- Never use the backing paper or the application tape/transfer tape to position the frosted window film on the glass. Always use the frosted window film itself. So you correctly position the film at the correct location.
- Use your supplied free squeegee. Start in the middle/centre of the window film and move horizontal or vertical with overlapping movements towards the edge of the window film. During which you hold the window film a couple centimetres (2 inches) above the window/mirror itself.
- Check to see if there is still any air trapped between the window film and the window itself. In the rare occasion that air is still trapped between the window and the window film. Gently push the air bubble to the edge of the window film (nearest part of the window not covered with window film). No need to use force.
- If you do not succeed without using force, use a pinprick to burst the air bubble.
- Allow the adhesive enough time to stick to the window. So that removing the application tape does not lift the frosted film from the surface/window/mirror. Remove the application tape after a couple of hours.
- If, when removing the application tape, you lift the window film from the window glass. Wait 24 to 48 hours before removing the application tape.
Applying frosted window film.
Above you find a number of photos during the application of frosted window film. for your information.
Below you will see the process and transformation of living room, kitchen en scullery windows. From the before situation of windows with curtains to the after situation of windows with frosted window film.
Below you see the application of frosted window film. First you see a number of photos/pictures with frosted window film on only the inside of the window glass. After applying a second window film on the outside you see a number of photos of the end result. Complete privacy with a cut out design perfect for in the bathroom.
Also, see our YouTube Channel for other instruction videos about applying window films and wall stickers.
Frosted window film photos after application
Below you find a great number of frosted window film photos. For at home and around the office.